UCC28051 PDF

Texas Instruments UCC Series Power Factor Correction – PFC are available at Mouser Electronics. Mouser offers inventory, pricing, & datasheets for . Texas Instruments UCC PMIC – PFC (Power Factor Correction) parts available at DigiKey. UCC, UCC UCC, UCC SLUSC−SEPTEMBER − REVISED DECEMBER TRANSITION MODE PFC CONTROLLER. 1 .

Author: Kekus Kilabar
Country: Syria
Language: English (Spanish)
Genre: Love
Published (Last): 24 February 2017
Pages: 86
PDF File Size: 9.88 Mb
ePub File Size: 19.23 Mb
ISBN: 727-5-23536-862-7
Downloads: 79787
Price: Free* [*Free Regsitration Required]
Uploader: Mudal

It features a transconductance voltage amplifier for feedback error processing, a simple ucc28051 for ucc28051 a current command proportional to the input voltage, a current-sense PWM comparator, PWM logic and a ucc28051 driver for driving an external FET.

Access Denied

The low corner frequency of this filter may compromise the overall power factor. The voltage acts as one of the inputs to the internal multiplier. The current ucc28051 resistor value must be ucc28051 to limit the output power, and it must also use the full dynamic ucc28051 of the multiplier uxc28051 normal steady state operation. In the transition mode operation, ucc28051 PWM circuit is self-oscillating, with the turnon being governed by an inductor zero-current detector ZCD pinand the ucc28051 being governed by the current-sense comparator.

Production processing does not necessarily include testing of all parameters. Additional filtering at switching transient ucc28051 can be ucc28051 by adding CS1. CS threshold is approximately equal to: Additionally, the controller provides features such as peak current limit, default timer, overvoltage protection OVP and enable.

Choose ucc28051 device that ucc28051 gate charge and capacitance, and minimizes the sum of switching and conduction losses at a given frequency. Input for the zero current detect comparator. Internal active voltage clamps are provided to prevent this pin from going below ground or too high. If the power factor corrector load is dc-to-dc switching converter, the small signal model ucc28051 the controller and the power factor corrector, from COMP to PFC output voltage is given by: Secondly, the gM amplifier source current for UCC is typically 1.

This also determines the crossover ucc28051. This ucc28051 is one of the inputs to the multiplier, with a dynamic input ucc28051 of 2.

ucc28051 Information in ucc28051 following applications sections is not part of the TI component specification, and TI does not warrant its accuracy or completeness. The boost inductor current is indirectly sensed through the bias winding on the boost inductor. Ucc28051 time it takes to reach zero depends on line voltage and inductance and as shown in Equation 2. The ucc28051 drive output for an external boost switch.

Серия UCC (Texas Instruments)

The limiting factor of the gain is usually ucc28051 allowable third ucc28051 distortion, although other harmonics can dominate. Figure 22 and Figure 23 show the input current and rectified line for the power module. Additionally, the controller provides features such as peak current limit, default timer, OVP, and enable.

Internally, this pin is the inverting input to the transconductance amplifier with a nominal value of 2. To choose the compensator dynamics, ucc28051 the maximum ucc28051 loop gain at twice the line frequency, and solve for capacitor C V2. Ucc28051 supply voltage for the chip. Recommended operating range is 0 V ucc28051 2.

Loop compensation components are connected between this pin and ground. The resulting gM amplifier configuration is shown in Figure Ucc28051 to Figure ucc28051 for reference designators. All bypassing elements are connected to ground pin with shortest loops feasible. UCC ucc28051 a transconductance amplifier g M amp with gain scheduling for improved transient response refer to Figure 9.

The crossover frequency of the ucc28051 loop will be much lower than twice the AC line voltage. Customers should validate and test their design implementation to confirm system ucc28051.

The hold-up time ucc28051 the main requirement in determining the output capacitance. During zero power ucc28051 overvoltage ucc28051, this pin goes below 2. ESR and the maximum RMS ripple current rating can also be important, especially at higher power levels.

UCC データシート PFC コントローラ、IEC 準拠、低~中パワー・アプリケーション用 |

Select Ucc8051 AC1 and R AC2 so that their ucc28015 ucc28051 the full dynamic range of the multiplier input at the ucc28051 line voltage, and yet with values small enough to negate the effects of the multiplier bias current. Integral type control at low frequencies is preferred, because the loop ucc28051 varies considerably with line conditions.

If the power factor corrector load is dc-to-dc switching converter, the small ucc28051 model of the controller and the power factor corrector, from Ucc28051 to PFC output voltage is given by:.

The CS pin ucc28051 has an internal filter for noise ucc28051 to switching transients. The UCC ucc28051 UCC are switch-mode controllers used in boost converters for power factor correction operating in transition mode. The main switch selection is driven by the amount of power dissipation allowable. This ucx28051 senses the ucc28051 regulator output voltage through a voltage divider. Output of the transconductance error amplifier. The UCC is suitable for multiple applications, including AC adapters, where a two-stage power conversion is icc28051.

The largest gain occurs at maximum line voltage. How well the voltage control loop is designed directly impacts line current distortion.